Ultrasonic Testing Equipments

Product Details:

 

DIGISCAN DS-333 is built tough and easy to use. Full size access to all the functions. The large, high resolution display has a wide viewing angle and good key board ensures direct visibility in any light conditions.

The TFT colored display has the ability to display small echoes which are very relevant to demanding UT operators, it does not miss any information. The DAC is offered in accordance to demanding customers needs.

DIGISCAN DS-333 is a complete instrument suitable for most applications where Ultrasonic Testing is carried out. It's simplicity to use, versatile features and ability to display high fidelity Ultrasonic signals, makes it an ideal choice for Axle Testing.

Features:

• Operation with Li-Ion Battery
• 3 Kg weight with batteries
• Receiver Bandwidth range from 1MHz to 6MHZ
• Selectable transducer modes: single, dual and angle beam
• Dual gate for accurate thickness measurement
• Built in trigonometric function for precise flaw detection
• Internal triggering
• Gated zoom facility to view expanded portion of the defect
• Selectable logic for both gates
• Background reference echo pattern for easy comparison of the defect
• 10000 ‘A’ scan memories
• 100 calibration sets
• USB interface for data logging

LCD Display:

• Display: TFT color LCD with LED back light, 300 X 200 pixel, 120mm (W) X 90mm (H) Pixel density 320x R.G.B(H) x 240(V)
• Display Freeze: Current display freezed
• Active Freeze: Display accumulation, active freeze echo to be saved
• Reference Echo Pattern: Reference pattern can be displayed at the background from selected location in memory
• Display Pattern: Unfilled or Filled

PULSER / RECEIVER:

• Receiver Bandwidth: 1MHZ to 6MHZ by broad band amplifier
• Gain: Total gain 120dB, 0–80dB operatable, 0.1,0.5,1,2,6,12dB selectable
• Rejection: Linear (0 – 99%)
• Operating Mode: Single Probe T+R, double probe T/R
• Test Mode: Pulse reflection or pulse Transmission
• Energy: NOR/LOW selectable
• Probe Zero: 99.99us in step of 0.1mm
• Vertical Linearity: Within ±3% on all ranges
• Probe Connector: BNC type
• Echo Display: Full wave rectified

Time Base:

• Range: 5mm min. –5000mm. Max (@5890M/sec)
• Delay: 0-3000mm continuous variable in step of 0.1mm, 0.01mm/step for 10-100mm, 0.1mm/step for 100mm–1Mtrs, 1mm/step for 1Mtr–5Mtr
• Monitor Gate: 2 Gates - Width 1/10 screen to full screen, Height 1/10 screen to 99%, Gate start measured from '0' div & ± logic selectable

General:
Memory:

• Minimum 10000 Sets data set-ups along with ‘A’ scans with calibration Parameters, trigonometric values and Label
• 100 calibration parameter sets
• Recalling the cal-sets, Frame set and labels as and when required

Interface / Outputs:

• PC connectivity via USB-A, with Export function opening in MS Word / PDF
• Pen Drive Connectivity via USB-B.
• Direct Printer Connectivity-Dot matrix Printer-DB9 Connector

PC Software:
EECOWIN PC interface software with Suitable port & transfer software. Can upload “FRAME” from saved set to PC through the USB port and through Pen drive.

Power Source:
Li-ion battery 3.7V max, 20800mAH
Rechargeable battery model BAT324l
-Operating time 8Hrs (min) with battery
-Battery charger cum mains adaptor 100-240V, 50Hz/60Hz, Model
-AD5V5 Full charge in 8hrs
-External charger model CGR322 with automatic cut-off facility to protect battery from over charging

 

Additional Information:

• Item Code: DS-333

Product Details:

The New Generation Ultrasonic Flaw Detector DIGISCAN DS-324 combines EECI’s years of experience & commitment to customers, to provide the best flaw detector in its category by way of most advanced Technology, Convenience, Uniqueness, Affordability & Technical options for ultrasonic applications in the market.

The TFT colored display makes the A-scan representation stable and clear in all types of lighting condition. Equipped with inbuilt Highest Reserved Gain and Universal DGS, makes DIGISCAN DS-324 a complete solution in ultrasonic testing. The Rugged, Lightweight, Ergonomical design enables the operator to use DIGISCAN DS-324 in any environmental conditions.

Key Features:

• Unique Technology with an inbuilt Flaw sizing Universal DGS
• Highest Reserved Gain Flaw Detector in its category of equipment
• Improved S:N ratio with advance hardware
• User friendly interactive architecture
• Direct data transfer through Pen Drive
• A-Scan recording
• Simplified, easy to access navigation key
• Tough, Light Weight & durable Industrial grade body
• Large, bright, crystal clear CRT grade display
• Standard/ Dynamic DAC for flaw sizing
• Li-ion battery

Display:

• The DIGISCAN DS-324 provides a LCD (320 x 240 pixels) display resolution
• The display is unique in its category, providing excellent A-Scan representation and readability of minute features of the signal
• The display also incorporates 4 colors Schemes & grids/ graticule pattern to suit all type of individual operator levels/ preference
• Zoom function makes each and every minute echoes visible to the user

PULSER/RECEIVER:

• Receiver bandwidth: 0.5 to 20 MHz by wide band amplifier.
• Gain: 0-80dB, 0.1, 0.5, 1, 2, 6, 12dB Selectable
• Rejection: Linear type (0-99%), 1% step, partial rejection (0-25%), 1% step.
• Operating mode: Single probe, double probe
• Test mode: Pulse reflection or pulse transmission
• Energy: HI/LOW selectable
• Damping: NOR/HI selectable
• Vertical linearity: 5% (±2.5%)
• Probe connector: BNC type
• Echo display: Full wave rectified

Time Base:

• Range: 5mm min.-5Mtrs. Max (@ 5890M/sec), Continuous Variable, (0.1mm step for 10-100mm, 1mm step for 100mm-5Mtrs.)
• Probe Zero: 0-99.99mm

Monitor Gates:
2 Gates
-Width 1/10 screen to full screen
-Height 1/10 screen to 99%
-Gate start measured from '0' div
-± logic selectable

Memory:
-190 Memory Sets with 'A' Scans Frames, Calibration Parameters, Trigonometric Value, Label (ID Tag)
-190 Calibration Parameter Sets
-190 DAC Sets

PC software:
EECOWIN PC interface software compatible with Windows 8 64bit. Can upload A scan saved set to PC and Pen drive through the USB Port.

Additional Information:

• Item Code: DIGISCAN-DS-324

Product Details:

Simplest user interface in the industry

• 16 active channels up to 200 v
• Multiplexing over 128 elements
• Supports two mono-transducers
• Time-of-flight diffraction (TOFD) is also available on the cartridge.
• 100 Mhz, 16 Bits. 512 Focal Laws, ACG, TCG and much more
• Ready for most applications without extra options
• Modular system ready to accept ECT, UT, EMAT

Pulsers:

• Pulser : +/- 100V (200 Vpp) Bipolar Square Wave
• Burst : up to 5 cycles
• Max. Pulse Repetition : 5 to 4000 Hz, manually

Beamforming:

• Max. Nb of Laws : 128 (S-scan) , 256 (L-scan)
• Amplitude : Static per probe element
• Calibration : Dynamic per beam (ACG)
• Dynamic Focusing:  up to 5 zones

CONNECTORS :

• PAUT Probe : I-PEX 30046 (Omniscan)
• Encoders, : LEMO 9-pin model
• Input/Output : FGG.OB.309

Receivers:

• Channels :  16 actives, 128 Multi-plexed
• Max. Input Signal Amplitude : 625 mVpp
• Input Impedance : 50 Ohms
• Input Bandwidth : 0.5 to 25 MHz @ -3 dB
• Gain : O to 80 dB (with TCG)
• Receiver Delay : O to 10.2 us, 5.0 ns step
• Digitizing : 100 MSPS, 12 bits per channel
• Digital Filters : 6 presets, user adjustable
• Rectification : Full, unipolar +/-, RF

 

Product Details:

The New Generation Premium Ultrasonic Flaw Detector Advanscan AS-414 combines EECI years of experience and commitment to customers to provide the best Flaw Detector In Its category by way of most advanced technology, convenience, uniqueness, affordability & technical options for ultrasonic applications in the market. The New Generation Ultrasonic Flaw Detector Model AS-414 incorporates the latest and most advanced Hardware & Software available in its unique friendly Interactive Architecture. The Hardware architecture includes Single Board Computer Circuitry for Best performance. The Software is based on the latest Windows platform with open architecture enabling it to upgrade and configure to any required applications. The Tunable Square pulsar offers best S:N ratio. The large, High definition LCD display provides unmatched. stable & clear A-Scan representation in all type of lighting conditions. The rugged. lightweight, ergonomical conditions. The rugged, lightweight, ergonomical design enables the operator to use in any environment
conditions.

Display:

• Viewing Area (HxW), diagonal: 115 x 95mm, 149mm
• Pixel Density: 640 x 480
• Display Type: TFT color LCD
• Display Freeze: Current display freeze selectable.
• Active Freeze: Display accumulation selectable.
• Reference Pattern: Reference A scan pattern can be displayed at the Background from selected location in Memory.
• Display Pattern: Unfilled or Filled.

Pulser:

• Pulser: Tunable Square wave, selectable frequency. Single or up to 6 pulses in ''Burst'' mode
• PRF: Variable 1000Hz. Auto limiting for set parameters
• Pulse power: Hi/Lo selectable
• Damping: 50E/1 K selectable

Receiver:

• Receiver Bandwidth: 0.5 to 20MHz by wide band amplifier.
• Digital Filter Setting: Selectable Low and High cut off frequency, in steps of 0.1 MHz. Adjustable between 0.1 MHz to 12 Mhz.
• Gain: 0-120dB variable in 0.5dB step. Step size selectable decimal, unit or tens value
• Rectification: Full wave/Positive Half wave/Negative Half wave, RF, selectable.
• Horizontal Linearity: ±1%.
• Rejection Amplitude: Linear type (0-99%), 1% step.
• Measurement: 0 to 100% full screen.
• Measurement rate: Equivalent to PRF in all modes
• Vertical Linearity: ±3%

Calibration

• Operating Mode: Single probe, Double probe, T-R mode
• Test Mode: Pulse, reflection or Pulse Transmission
• Units: Millimeters or Microseconds Selectable
• Range: 5mm min.-tomtrs. Max @5890m/sec. Continuous variable in 1mm step. Step size selectable decimal, unit or tens value.

Monitor Gate:

• 1 interface Gate for immersion mode
• 2 independent Gates with selectable
• Width 1/10 screen to full screen
• Height 1/10 screen to 90%
• Gate start measured from initial pulse
• ± Logic selectable, Audio Alarm/Mute.

 

Measurements:

 

Trigonometric:

• Beam path, Flaw depth and Projection
• Distance Functions displayed for selected
• echo within Gate 1 and Gate 2.
• Angle selection 0° to 90°.
• Job thickness selection 5 to 999.9mm.

 

Measurements:

• Within Gate 1 and Gate 2.
• Echo height displayed in %
• Echo Amplitude displayed in dB

Additional Information:

• Item Code: ADVANSCAN-AS414

Product Details:

Qualities

• DS-5XX is a Multi-Channel Digital Ultrasonic Flaw Detector
• It uses latest in Micro-Component technology to give features and performance not found to its class of equipment.
• It’s channels are independently adjustable for Gain, Range, Gate and other parameters.
• Each Channel has alarm LED which are prominently placed for operator visibility.

Specification:

• Receiver bandwidth : 0.5 to 15MHz by broad band amplifier.
• Gain : 0-80dB, 0.1,0.5.1,2,6, 12dB selectable
• Rejection : Linear type (0- 99%) of full screen ,Height, 1% step Rejection will be ,displayed in single channel mode. In run all mode it will not be visible.
• Operating mode : T-R, T+R by external connection.
• Test mode : Pulse reflection or pulse Transmission
• Echo display : Full wave rectified
• Vertical linearity : 5.00%
• Range : 10mm min. - 725mm. Max (@5890M/sec) -Continuous variable
• Delay : 0-1000mm continuous variable
• PRF : In built . Auto limiting for set parameters
• Velocity : Velocity 2000m/s to 9999m/s
• Time base linearity : 1% (±0.5%)
• Triggering : Internal
• Monitor Gates: 2 Gates for all channels, Width 1/10 screen to full screen; Height 1/10 screen to 99%; Gate start measured from initial Pulse
• Monitor Logic : +/- Logic selectable

Alarm

• Audio/visual (Audio mute)
• Each channel will have RED LED
• For gate1 function and GREEN LED
• For gate2 function
• Trigonometric : Beam path, Flaw depth & Projection Distance
• Functions TRIG (Job thickness) : 0.1 to 300mm

Measurements

• Echo height- ± 1.0% tolerance
• Thickness (Echo to Echo) - + 0.1mm or + set range/300 whichever more with peak & flank option.
• Parameter Display : Permanent display -Horizontal & vertical graticule. Common display for all channels-Lock, Battery status, zoom, Freeze, Active freeze. Display for individual Channels---Gain, Beampath, Flawdepth/Thickness, Projection Distance, Envelop, Probe zero, Delay, Range, Reject, Gate1/Gate2 ON/OFF, Gate shift, Gate Width, Gate height, alarm mute, Configuration menu, Memory save, Memory recall.
• Display Scheme : Any one channel on one A scan trace or four A scan traces with two channels each are displayed. Current display freeze & Active freeze, Accumulated display
• Display Pattern : Filled / Unfilled
• Reference pattern Display : Reference pattern can be displayed at the Background from selected location in Memory
• Graticules : 5div(H) X 5div(V), further sub divided into 10 small divisions
• Battery Indicator : Battery status indicator with auto shut Down
• Memory : 200 multicolored ''A'' scans memory , with calibration parameters and trigonometric values , 15 calibration sets.
• Interface : PC & pen drive connectivity via USB

Trace Color :Selectable white and black background;

• CH-1 ---WHITE;, CH- 2--GREEN;
• CH-3—-ORANGE; CH4---LlGHT BLUE;
• CH-5-PINK; CH6---YELLOW;
• CH-7m-BLUE; CH-8-mOTHER COLOR
• PC software : EECOWIN PC interface software Can upload saved "FRAME" set to PC through USB
• Accessories : Li-ion Battery pack. External Battery charger cum mains Adaptor Input 90-240V AC, 50-60Hz. Protective case. Instruction manual.

 

Additional Information:

• Item Code: DS-5XX

Product Details:

We are a leading manufacturer and supplier of Ultrasonic Thickness Gauge.

• Sealed Touch Key Pad
• Auto Calibration For Mild Steel
• Big LCD Display
• V­ Path Corrected For High Accuracy
• Long Working, with ‘AA’ size cells
• Wide Range of Probes Compatibility
• Small Pocket Size
• Metric English Conversion
• Micro Processor Based
• Surface Mount Device Technology
• Stable, Repeatable & Accurate

Specification:

• Testing Method : Pulse echo, transit time measurement
• Range : 1 mm to 199.9 mm, Thickness range depends on material, transducer type, surface condition and component temperature
• Probes: Dual Crystal, Transmitter - Receiver type
• Key pad : Sealed colour, coded Key Pad
• V-Path : Micro-controller corrected
• Calibration : One Step calibration on known thickness specimen
• Zero Calibration : Auto \ manual calibration (selectable)
• Display : Measured thickness, Coupling check, Battery Check, Velocity, over range, CAL mode, Error, Software version, Probe number
• Memory (ETM - 2) : Holds last measured reading and calibration
• Battery : 2'AA' size disposable cells 30 Hrs. normal operating time with alkaline cells
• Low Battery : Indication on display
• Auto power Off : Unit Will shut OFF approximately 2 minutes after last use or when  battery voltage is too low for reliable measurement
• Ambient Temp. : 0° C to 45° C.
• Case : Weather resistant, moulded plastic

Additional Information:

• Item Code: ETM-2

Product Details:

Features

• Dual, Single, Delay line Transducers
• Measuring Range 0.8mm to 499mm
• Large LCD display with Back Light
• Raw material, Finished Components, Shop Floor, Laboratory, Site.
• Alarm mode and differential mode

Specification:

• Thickness Measuring Range: 0.8mm 499mm ( 0.030 to 19.96 inches) in steel@& Velocity 5890 M/sec. (dependent upon job, & Probe Type).
• Velocity Range: 700 M/Sec to 14000 M/Sec (0.0275 to 0.551 inches/U Sec).
• Measurement Rate: Two readings per second.
• Resolution: 0.01mm (0.0004 inches) for less then 100mm and 0.1mm ( (0.004 inches) for above 100mm (dependent on probe type).
• Transducer Frequency Ranges: 1MHz to 15MHz in Single, Dual & Delay line Mode.
• Other Measurements: Through Coat, Thickness
• Accuracy: ±0.06mm (dependent on job and probe type).
• Units: Millimeters or Inches.
• Auto Off: 120 Seconds after last operation or on low battery.
• Key Pad: Sealed Tactile Keys, Keyboard lock mode selectable.
• Operatiing Temperature Range: 0 to 55° C.
• Calibration: Either using calibration block or Velocity entry or using known thickness block of required job material.
• Smart Functions: 1 Differential Thickness (measures deviation from user defined reference value)
• Alarm (when user defined high or low thickness limits are crossed).
• Optimize thin(suitable for lower thickness, factory set parameters).
• Optimize thick(suitable for Higher, factory set parameters).
• Optimize thick (suitable for higher thickness factory set parameters).
• Probe Type: Single Probe, Dual Probe or Delay Line Probe.
• Probe Connection Type: Mini-Lemo connector, Microdot for D-155.
• Datalogging(ETM3DL): Data logger wih memory for thickness 4000 readings.
• PC Connectivity (ETM3DL): USB port & Cable for easy connectivity & data transfer to PC
• PC Transfer Software (ETM3DL): Transfer Software included with standard Kit.
• Power Supply: 4,'AAA' Alkaline cells or Optional Rechargable batteries with charger/Adaptor (230VAC).
• Standard Kit contents: Instrument Protecting cover, Operating mnual, SB-2 block and Carrying case.
• Optional Accessories: Probes of various types, Calibration Blocks, Couplants and probe cables.

Product Details:

Features

• 8 individually programmable channels
• Two gates per channel
• Frequency Range 0.5-15 MHZ bye wide band amplifier Large CRT with bright display
• 4 digit 7 segment LED display to indicate Gain, Gate, Range, Memory etc.
• Free from distortion & parallax error
• Selectable PRF
• 9 sets of calibration Memory
• Output for Recorder available

APPLICATIONS OF PI-D08

• Multichannel Plate Testing Trolley for internal defects (Laminations/ Slag)
• Edge Scanning of Plate / Coil (On-line)
• Low cost systems for testing Bars, Tubes & Pipes, ER Pipes
• Component testing systems

Additional Information:

• Item Code: PI-008